Oblong Adapter tip for older or square grand pianos with oblong tuning pins. The square chucked end fits into the star tip of any tuning lever. LEVER NOT INCLUDED

Action Screwdriver with wooden handle Slot End. Made by Renner

Action Screwdriver with wooden handle Pozi End. Made by Renner

Set of washers for Grand Lever regulating Screw containing baize and leather washers. Made by Renner

Pack of travelling papers consisting of 2 thicknesses (Red and Blue 5 gram each). Self adhesive backed. To slightly alter the movement angle of the hammer travelling towards the string.

Jack and Drop Screw Regulator

Flush Cutters made from highest grade thick carbon steel. 6" cutter with rubber grip. excellent for use with center pins and soft wire.

PVC-E GLUE is an excellent adhesive for key covers, cloth, felt and leather material. This glue dries clear and can be thinned up to 5% with water.

Grand Back Check Leather 400mm x 55mm. 1.9mm thick.

Grand Back Check Leather 400mm x 46mm. 1.9mm thick.

Let off Tool for S & S

Boxed set of ivory colour key Coverings, with fronts standard size: 50mm head

Grand double wing springs for grand lever bodies (whippens).

Alcohol burning lamp for casting hammers. Brass with cap.

Let Off Tool. Perfectly fits old and new Steinway regulating screws.

Renner Grand Action Model

Renner Upright Action Model

For insertion of paper punchings when leveling keys. 24cm.

For insertion of paper punchings when leveling keys. 16cm.

Loop cord, Green, 10 Meter length by Renner.

Individual voicing block

Tightly wound with flexible shaft this strong magnetic pick up tool snakes easily into hard to reach areas.

Strip of Red Bushing Cloth 1.2mm for flanges in grand and upright pianos. With glued point for easy threading.

Easily inflated compact air bag for raising pianos approximately 2 inches.

An assorted box of cloth balance rail and baize front rail washers. Ideal for emergency repairs.

Jack Alignment Tool, Aluminium, for Grand whippens.

Key easing tool with two ends. One end permits easing of the key pin hole without removing the key. The reverse wedge in the other end enables oversize key pin holes to be closed slightly to tighten the key.

V275 Double Head Screwdriver with handle. Ideal for reaching inaccessible screws like Bluthner patent action screws

An assorted box of paper and card balance rail and front rail washers. Ideal for emergency repairs.

Set of 3 key dip blocks 9.5/10/10.25 in a compact wooden box (covered with felt): 100 x 45 x 22mm

A unique portable book holder for upright pianos. The clip provides a secure way to hold your sheet music. No screws or drilling required.

H Flange for Steinway Upright. Available in Bass (0.85), Middle (0.80), Treble (0.75), or Top Treble.

Designed primarily for regulating the dowel type capstans on Yamaha upright pianos with a narrow end to accomodate the small holes in the capstan dowels. Complete with wooden handle.

The V287 combination regulating 'T' handle allows for greater pressure to be exerted for those difficult situations. The handle is 4'' long and has a 3'' chrome plated shaft and collar.

Thumb held toning tool complete with needles and safety guard.

A standard key dip block to level black and white keys.

10cm of 9mm Red Check felt. (Width of roll 1.50 metres)

Clip on bridle tap inserter. A moulded plastic saddle at the end of the wood shank accepts the brass spring clip for easy insertion of the bridle strap on to the hammer butt.

Celeste Pedal shift lock

Guide Roller for celeste cable.

For insertion of paper punchings when leveling grand keys with the action in place.

This tool works by grasping the string at the speaking length directly behind the agraffe or V bar. By gently tilting the tool backward or forward, one can raise or lower the level of the string. Made from high strength steel

The holding block suspends a ½” rule over a two or three string unison. Pluck the string with the dampers raised, when all the strings vibrate against the edge rule, the strings are level.

Small handy finger held tool with two ends. One end ideal for the grand drop screw the other for the repetition lever. Both ends illustrated.

The key pounder helps spread out and minimize the stress from key strikes. If you tune professionally, you are placing an enormous strain on your fingers, hand, wrist and forearm by striking piano keys thousands of times per day. Optimal size to strike ei

Bass string twister for twisting rattling or numb strings.

Balance hole reamer. 2 blades for cleaning and polishing off the balance hole.

Hammer fitting block for filing hammer heads to fit string level.

Single Needle Toning Tool with long handle for toning grand pianos without the need to remove the action. Ideal for final voicing.

These strongly constructed braked units have four 4 inch single wheeled castors supporting each leg. These larger wheeled castors are ideal for easy movement over uneven floors. Only raising the piano 2cm Weight load 900kg.

CA adhesive super thin glue for penetrating and stabilizing soft wood.

Wrest Pin Box Small, Easy to store and carry wrest pin box for those on the road repairs. Contains 10 pins of each of the 8 most commonly sold blued pins plus 10 nickel pins. Complete with 10 metal bushings and chalk.

Ruck sack style tool case with 5 elastic tool holders,document pouch and large front compartment.

Micro Fibre Piano Cleaning Cloth Use the cloth dry to dust the exterior of your polyester piano. Unlike other cloths, the dust will cling to the fibres and will not spread to other areas. Sold Individually.

Carbon Tuning Lever (Main handle 19cm ) Head not included.

An excellent value buttoned vinyl seat adjustable concert stool. Flat packed with detachable legs. Only available in BLACK poly.